Clik here to view.
Re: VMFS Issue, FB Inconsistecy found, (xxx,xxx) allocated in bitmap but...
Ulli, thank for the insight regarding the "allocated in bitmap" messages... I suspected they were innocuous. And... I absolutely agree with your assessment regarding VMware and how they treat VMFS --...
View ArticleRe: URGENT - repeated ESX crashes
I'm not familiar with IBM hardware, but often servers have an integrated "self-protection" which means thy may reboot or power off in case they detect failures (e.g. a cooling issue). I'd recommend you...
View ArticleClik here to view.
Re: VMFS Issue, FB Inconsistecy found, (xxx,xxx) allocated in bitmap but...
Thanks for the good compiled list. Suggestions/Comments well taken the fs checker does exist for VMFS from long time. its just that not all bells and whistles are exposed to end users due to the...
View ArticleRe: VMPlayer Can't detect scanner for All-in-one printer?
Do I understand correctly:-It is a network printer.-It is connected to the Host.-It is not connected to the Guest, but you can print anyway, using the Virtual Printing feature. If that is the case, it...
View ArticleHA with insufficent capacity in cluster
We had a HA Cluster with two Host 5.1, all VM run in the first host (12 VMs), and vCenter Appliance Linux.When we disconnected of the energy the first host (shut down simulation), the second host only...
View ArticleRe: unable to Collect Logs Errror:Unable to connect to the Remote Server
I'm not sure their reasoning for that, but it seems like a pain in the butt. Why don't you just export the logs with the vSphere Client? File -> Export -> Export System Logs Or Use the vSphere...
View ArticleUsing VMA to edit vpxa.cfg on multiple ESXi
I am replacing the IP address on one of our vCenter servers. I have all the info for the Update Manager and the info for changing the vpxa.cfg but I wnated to know if there is any way for me to run...
View ArticleRe: HA with insufficent capacity in cluster
When your first host goes unavailable, you would see the "insufficient resources to satifiy HA" message regardless, because, at that point in time, you do not have the resources to satify the failure...
View ArticleClik here to view.
vBeer Minsk
vbeer №1 Minsk состоится 2 апреля. время: после 17-00место: в процессе выбораусловия участия: технический интерес к виртуализации и неподдельно искренняя любовь к пиву.плюшки: присутсвие экспертов из...
View ArticleRe: Cant open VM - Dictionary problem
I found the contents of my vmsd file had been overwritten (i.e. corrupted) somehow.I deleted the vmsd file and used the snapshot manager to make a new snapshot. After that I was able to start my...
View ArticleFailback Operation
I just failed back from a recovery we were running on some test systems. I noticed that the original failover to our DR site unmounted all LUNs from our hosts and removed the LUNs from the storage...
View ArticleRe: LUN is invisible from ESXi hosts in cluster
HI Sai, PFB the inline is/was there data on the LUN? is the LUN coming from the same controllers as the other LUNs? There was a data, but after this issue happen LUN was detected to one server after...
View ArticleClik here to view.
Re: Cant open VM - Dictionary problem
I deleted the vmsd file and used the snapshot manager to make a new snapshot. If that is literally all you did then you have an orphaned snapshot or several orphaned snapshots that you'll eventually...
View ArticlevCD - Configure org VDC Networks
Hi There,I have an Organization Admin account to my organization virtual data center. I want to to change the DHCP configuration for the network. When I log in to vCD, select my organization network,...
View ArticleRe: ESXi through VLAN
STP is enabled but I don't believe that switchport mode access is enabled. I will attempt to enable it. Could this still be the cause even though I can remote in to the host with the vsphere client?
View ArticleClik here to view.
Re: Moving VM's with 2 vNIC's from a dvSwitch to a vSwitch?
Let me know how far you get with Gabe's script.If you're stuck don't hesitate to ask here. Yes, I'm the same LucD
View ArticleEndpoint Agent issue
I have installed vCAC and am working on getting the endpoint functioning, i created the endpoint and installed the agent. During the agent install i am using http as the transport protocol. when i...
View ArticleRe: OS X 10.8.2 Guest freezing up with 100% CPU usage
Hi GoDeveloper, We're working with Apple to investigate an issue where Mac OS X 10.8.x freezes (with 100% CPU usage) if it only has 1 processor core available and it starts running low on memory. It...
View Article